Brother Label Maker PT 7100 User Manual

[GETTING STARTED]  
REFERENCE  
PREPARATION  
OPERATION  
3
1
2
Power Supply & Tape Cassettes  
Troubleshooting  
Keyboard & LCD  
Error message  
Open the tape compartment  
cover by pressing in the rough  
area at the top end of the  
machine.  
If a tape cassette is already  
installed, remove it by pulling it  
straight up. Also, if batteries are  
already installed, remove them.  
• Make sure that the power is  
turned off when replacing  
batteries or tape cassette.  
Tape compartment  
cover  
USER'S GUIDE  
Size  
Message  
Cause/Remedy  
English  
/ Español  
Width  
Style  
Battery  
The batteries are weak. Replace them with new ones.  
The installed batteries are about to run out.  
BATTERY!  
Invalid  
Printed in China  
LW3522001  
• There is no text above the cursor when you set Numbering.  
• Invalid character is selected for Numbering.  
• Invalid number is selected for Tab Length or Label Length.  
Cursor  
Underline/Frame  
Label Length  
Print  
head  
Caps  
Time/Date key  
Power key  
No Text  
You tried to print a text file when there is no data stored in  
the memory.  
• The Print key is pressed when no text is entered.  
You tried to set Copies, Numbering, Mirror, or Text Preview  
when no text is entered.  
Print key  
Enter key  
Cursor key  
Clear key  
Number key  
Backspace key  
Function key  
Tape cutter lever  
Insert six new AAA alkaline  
batteries (LR03), making sure  
that their poles point in the  
correct directions. Always  
replace all six batteries at the  
same time using brand new  
ones.  
Line Lmt  
You tried to enter a 3rd line by pressing the Enter key.  
You tried to print a 2 line text when 9/64" (3.5mm) or 1/4"  
(6mm) tape is installed.  
INTRODUCTION  
No Cassette  
Cutter Error  
Full  
You tried to print a label when there is no cassette installed.  
Tape cutter lever is used in the middle of printing process.  
With your PT-7100, you can create labels for any application. Select from the  
many frames, character sizes and styles to design beautiful custom labels. In  
addition, the variety of tape cartridges available allows you to print labels with  
different widths and exciting colors.  
Read this manual carefully before starting and keep the manual in a handy  
place for future reference.  
The maximum number of characters (80 characters) have  
already been entered.  
Character key  
Text Lmt  
The text length exceeds the selected label length or the  
selected Auto Format setting length.  
Caps key  
Symbol key  
Accent key  
Space key  
No Frame OK?  
Printing on 9/64" (3.5 mm) tape with invalid Frame setting  
ON. (Select  
to print with no Frame,  
to cancel.)  
WARNING  
What to do when...  
Insert a tape cassette, making  
sure that it snaps into place.  
Always use the specified voltage and the suggested AC adapter (AD-24) for this  
machine to prevent any damage or failure.  
Problem  
Solution  
The display stays blank • Check that the batteries are correctly inserted.  
after you have turned on • If the batteries are weak, replace them.  
Unplug the power cord immediately and stop using the P-touch labeler during an  
electrical storm. There may be a remote risk of electric shock from lightning.  
Do not use the AC adapter in places of high humidity such as bathrooms.  
Do not overload the power cord.  
Do not place heavy objects on, or damage the power cord or plug. Do not forcibly bend  
or pull the power cord. When disconnecting the power cord from the power outlet,  
always hold the plug.  
To prevent fire or electric shock, make sure that the plug is fully inserted to the power  
outlet. Do not use an outlet that is loose.  
Do not get the machine/AC adapter/power plug wet, such as by handling them with  
wet hands or spilling beverages on to them.  
Do not disassemble or modify the machine/AC adapter/batteries.  
Disconnect the AC adapter, remove batteries and stop using immediately if you notice  
any abnormal odor, heat, discoloration, deformation or anything unusual while in use,  
or in storage.  
Do not use metallic articles, such as tweezers or a metallic pen, when exchanging the  
batteries.  
End of tape  
The LCD shows one row of 12 characters; however, the text that you  
enter can be up to 80 characters in length.  
Toothed Wheel  
the machine.  
• Check that the AD-24 adapter is correctly connected.  
When the label is  
• See "[Margin] (Tape Margin)" in this users guide and select  
[Half] or [Narrow] to have smaller margins for your label.  
printed out, there is too  
much margin (space) on  
both sides of the text.  
Cutter's edge  
Initial Settings  
Start your machine  
Supply power by using six AAA alkaline batteries or the optional AC adapter, and  
The machine does not • Check that the tape cassette has been inserted correctly.  
print, or the printed  
characters are not  
formed properly.  
• If the tape cassette is empty, replace it.  
• Check the tape compartment cover is properly closed.  
Tape guide  
then press  
.
The setting has cleared • The batteries may be weak. Replace them.  
Set the language (English/Español/Français/Hrvatski/Italiano/Magyar/  
Nedrlnds/Norsk/Polski/Portug./Română/Slovenski/Slovensky/Suomi/  
on its own.  
• When power is disconnected for more than two minutes,  
all text & formats in the display will be lost. Language, Unit  
and Time/Date settings will also be cleared.  
Tape exit slot  
Svenska/  
/Dansk/Deutsch)  
• Make sure that the end of the tape feeds under the tape guides.  
• If the ink ribbon is loose, use your finger to wind the toothed wheel in the  
direction of the arrow on the cassette.  
The default setting is "English".  
A blank horizontal line  
appears through the  
printed label.  
• There maybe some dust on the print head. Remove the  
tape cassette and use a dry cotton swab to gently wipe the  
print head with an up-and-down motion.  
>
[
Language]  
and press  
>
Do not throw into fire or heat up the battery.  
• Use only Brother TZ tapes with this machine.  
The machine has  
Turn off the machine, and then while holding down  
Choose a language with  
.
"locked up" (i.e., nothing  
happens when a key is  
pressed, even though  
the machine is on.)  
and  
, press  
to turn the machine back on.  
Securely close the back cover, making  
sure that it snaps into place.  
After you have installed the tape, feed the  
tape (see Feeding) once and then push in the  
tape cutter lever to cut the tape.  
CAUTION  
Set the unit (inch/mm)  
The default setting is "inch".  
Finally, release  
• Note: The text and formats in the display are erased. Also,  
the language, Unit and Time/Date settings will be cleared.  
and  
.
To avoid injuries, do not touch the blade of the cutter unit or any metal parts near the  
print head.  
Do not apply excessive pressure to the cutter lever.  
>
[Unit]  
and press  
>
The power turns off  
when you try to print.  
• The batteries may be weak. Replace them.  
• Check that the batteries are correctly inserted.  
Remove the batteries and disconnect the AC adapter if you do not intend to use the  
machine for an extended period of time. (Note: When power is disconnected for more  
than two minutes, all text & formats in the display will be lost. Language, Unit and  
Time/Date settings will also be cleared.)  
Do not use old and new batteries together or mix alkaline batteries with other type  
batteries, or set the positive and negative end in the wrong position. Otherwise, the  
batteries may leak or be damaged.  
To prevent damage or breakage, do not drop or hit the machine/AC adapter and press  
on the LCD display.  
Depending on the location, material, and environmental conditions, the label may  
unpeel or become irremovable, the color of the label may change or be transferred to  
other objects. Before applying the label, check the environmental condition and the  
material.  
Choose unit with  
.
The tape does not feed  
• Check that the end of the tape feeds under the tape guides.  
properly or the tape gets • The cutter lever is used while printing. Do not touch the  
Set Date (MM/DD/YY) and Time (hh:mm)  
Example: setting the clock to October 21st 2009, 10:30AM  
stuck inside the machine.  
cutter lever during printing.  
All text and format settings  
need to be cleared to  
create a new label.  
• Press  
and select [Txt&Format].  
When using optional AC adapter (AD-24)  
>
[TimeDate]  
input “21”  
>
[Clock]  
.
Insert the plug on the adapter cord into  
the adapter jack on the bottom end of  
the machine.  
To change language  
setting.  
• See step 2 "Set the language" of the "Initial Settings".  
Date (MM/DD/YY)  
>
>
>
>
>
Insert the plug into the nearest standard  
electrical outlet.  
For memory back up, we recommend using  
AAA alkaline batteries (LR03) together  
when using the AC adapter.  
Specifications  
input “10”  
input “09”  
Any data stored in memory will be lost due to failure or repair of the P-touch labeler,  
or if the battery expires.  
Time (hh:mm)  
Item  
Specification  
Dimensions  
4.3" (W) × 8.1" (D) × 2.3" (H)  
(107.4 mm (W) × 202.6 mm (D) × 56.6 mm (H))  
General Precautions  
Weight  
0.80 lbs. (365 g) (without batteries and tape cassette)  
input “10”  
input “30”  
and press  
Do not use the P-touch labeler in any way or for any purpose not described in this  
guide. Doing so may result in accidents or damage the machine.  
Use only Brother TZ tapes with this machine. Do not use tapes that do not have the  
mark.  
Power supply  
Six AAA alkaline batteries (LR03) or optional AC adapter  
(AD-24)  
Tape cassette  
Brother TZ tape (width) :  
9/64" (3.5 mm), 1/4" (6 mm), 3/8" (9 mm), 1/2" (12 mm)  
Select AM/PM with  
.
Do not clean the machine with alcohol or other organic solvents. Only use a soft, dry  
cloth.  
Do not touch the print head with your fingers. Use a soft wipe (e.g. a cotton swab)  
when cleaning the print head.  
Do not put any foreign objects into the tape exit slot or AC adapter connector, etc.  
Do not place the P-touch labeler in direct sunlight or rain, near heaters or other hot  
appliances, dashboard or in the back of your car, in any location exposed to extremely  
high or low temperatures, high humidity, or dusty locations. Standard operating  
temperature range: 50°F to 95°F (10°C to 35°C).  
Do not try to print labels using an empty tape cassette in the P-touch labeler. Doing  
so will damage the print head.  
Do not pull the tape being fed from the P-touch labeler, otherwise the tape cassette  
or P-touch labeler may be damaged.  
You can also confirm the figure and move to the next setting by using the right  
cursor key.  
Accessories (Supplies may differ by distribution.)  
• The machine automatically turns off if no keys are pressed within 5  
minutes.  
Accessories  
Stock No.  
See the included "Supplies and Accessories Guide".  
AD-24  
Tape Cassettes  
• To cancel operations, press  
.
AC Adapter  
Cutter Unit  
• To initialize the settings, turn off the machine and then while  
TC-5 (replacement)  
holding down  
and  
, press  
and  
to turn the machine back  
If the cutter blade becomes blunt and the cutter stopper wear after repetitive  
use and the tape cannot be cut cleanly, replace with new cutter unit (stock no.  
TC-5) by obtaining from an authorized brother reseller.  
on. Finally, release  
.
[CREATING LABELS]  
DESIGNING LABELS  
[Size]  
MAKING TEXT  
Switching Upper Case/Lower Case  
2
PRINTING LABELS  
COMPLETED LABELS  
1
3
4
(
+
)
(
+
)
)
Text Preview  
Upper case ( ON)  
Lower case ( OFF)  
You can preview the text before printing.  
>
[Size]  
>
[Large]  
>
[Preview]  
[Large]  
[Medium]  
[Small]  
The LCD shows the whole text and the label length (inch/mm), then returns to the  
original text.  
Only the text can be previewed, not the font, style, size, underline/frame or any  
additional features.  
Peel the printed label from backing and apply the label.  
Making Two Line Text  
Move the cursor to where the second line starts and press  
Automatically adjusts the text size according to the tape width.  
(
+
+
)
.
USEFUL FUNCTIONS  
[Width]  
Use either 3/8" (9 mm) or 1/2" (12 mm) wide tape for two line text.  
(
+
Feeding (Tape Feed)  
(
+
)
>
[Width]  
>
[×2]  
File (Memory)  
Display  
Label image  
[Normal]  
[×2]  
[×1/2]  
>
[Feed]  
You can save your original labels on to your machine. Up to nine labels can  
be saved and recalled for printing whenever you desire. You can also edit and  
overwrite the stored label.  
Printing  
Entering Symbols  
(
)
[Style] (Vertical)  
>
>
[File]  
>
>
>
>
[Style]  
>
[Vertical]  
To Save: >  
To Print: >  
To Open: >  
[Save]  
[Print]  
[Open]  
>
To cut off the label, push in the tape cutter lever on the upper-right corner of the  
machine.  
To prevent damage to the tape, do not try to cut while the message "Print" or "Feed"  
is displayed.  
When Chain Print is set, "OK to Feed?" will appear. (See the Note of [Chain Prt] in  
[Margin] (Tape Margin). )  
Group  
Symbols  
Group  
Symbols  
[Normal]  
[Bold]  
[Outline]  
1
10  
>
2
3
4
5
6
7
8
9
11  
12  
13  
14  
15  
16  
17  
[Shadow]  
[Italic]  
[I+Bold](Italic Bold)  
>
(
+
)
[Margin] (Tape Margin)  
[I+Outl](Italic Outline)  
[I+Shadow](Italic Shadow) [Vertical]  
If you try to store a label when there is already a label stored to that  
number, a message “Overwrite?” will appear. Press to save your  
new label. Press to cancel.  
>
[Margin]  
>
[Full]  
(
+
+
)
[Full]/[Half]/[Narrow] is for leaving equal margins on both sides of the text.  
NOTE: Cut along the printed dots (:) with scissors so the text is centered in the label.  
[Underline/Frame]  
(
+
)
Time/Date Function  
>
[Undl/Frm]  
>
[Undl]  
Full  
Half  
Narrow  
You can insert the desired time and date to your text at the touch of a button.  
8 Formats are available for printing time and date.  
You can change the number of time/date by changing the clock setting.  
ABC  
:
ABC  
:
ABC  
[Off]  
[Undl](Underline  
[Banner]  
)
[Round]  
[Candy]  
1"  
1"  
1/6"  
1/6"  
1/2"  
1/2"  
[Callout]  
[Wooden]  
[Chain Prt] (Chain Print) is for printing more than 1 copy of a label with min-  
imum margin <e.g. 1>. You can also create a label containing texts in various  
To go to the next group, press  
To cancel operations, press  
.
To add Time/Date to your text:  
.
styles; enter a text in one style and press  
. After that, cancel feeding (see  
Frames can not be printed on 9/64" (3.5mm) tape.  
the note below), and enter the second text in another style <e.g.2>.  
Chain Print  
Entering Accented Characters  
(
)
[Tab]  
The cursor should be positioned where you wish to insert the time and date.  
<e.g. 1>  
<e.g. 2>  
>
>
/
>
To select the format of Time/Date:  
You can make aligned texts by setting tabs.  
Example: To set a tab between "ABC" and "D"  
ABC  
DEF  
ABC ABC ABC  
ABC  
Accented Characters  
Accented Characters  
>
[TimeDate]  
>
The cursor should be positioned where you set a tab.  
(feed & cut)  
(feed & cut)  
A
C
D
E
G
I
a
c
d
e
g
i
>
>
[Tab]  
• FEED THE TAPE BEFORE USING THE CUTTER OTHERWISE A  
PART OF THE TEXT MAY BE CUT OFF.  
Display  
Label image  
Example  
Example  
• After pressing  
Press to cancel.  
• Do not try to pull the tape since this may damage the tape cassette.  
, "OK to Feed?" will appear. Press  
to feed.  
Format  
Format  
(October 21st 2009, 3:30PM)  
ABC  
D
(October 21st 2009, 3:30PM)  
Tab  
M/D/Y  
M/D/Y hm  
D/M/Y  
10/21/09  
D.M.Y  
D.M.Y hm  
Y-M-D  
21.10.09  
21.10.09 03:30PM  
09-10-21  
(
+
+
+
)
)
)
[Tab Length](Auto / 0.0" - 4.0" (0-100mm))  
10/21/09 03:30PM  
21/10/09  
(
+
)
Using [Print Option]  
K
L
k
l
>
[Tab Length]  
>
D/M/Y hm  
21/10/09 03:30PM  
Y-M-D hm  
09-10-21 03:30PM  
[Copies]  
You can print up to 9 copies of each label.  
You can also select the length by entering the length with Number keys.  
To return to [Auto], press  
N
O
R
S
T
U
Y
Z
n
o
r
To change the Clock Setting:  
See step 4 of the "Initial Settings".  
.
>
[Print Option]  
>
[Copies]  
>
(
[Label Length](Auto / 1.2" - 12.0" (30-300mm))  
FCC NOTICE  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)  
This device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
s
t
>
[Length]  
>
You can also select the number of copies by entering with Number keys.  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part  
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in  
a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  
You can also select the length by entering the length with Number keys.  
To return to [Auto], press  
u
y
z
[Numbering]  
.
You can print many copies of the same text while increasing a selected  
number by 1 after each label is printed.  
(
[Auto Format]  
Example: To print copies of a label containing a serial number (0123, 0124 and 0125)  
To cancel operations, press  
.
You can choose label length from six formats to create labels for various ap-  
plications.  
-
-
-
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s  
authority to operate the equipment.  
>
>
[Print Option]  
>
The order of accented characters differ by the selected LCD language.  
[Numbering]  
>
To Clear  
>
[A/F]  
>
[VCR VHS]  
Select the highest number you wish to be printed when setting the number.  
By pressing the Backspace Key, the letters will be deleted  
one by one.  
Application  
VCR VHS  
Mini DV  
Audio  
Length  
Application  
Length  
Should you encounter any problems with your product, please do not return  
your product to the store!  
[Mirror]  
5.5" (140mm)  
1.6" (42mm)  
3.5" (89mm)  
CD Spine  
File Tab  
Divider  
4.4" (113mm)  
3.2" (82mm)  
1.6" (42mm)  
>
[
Print Option  
]
>
[
Mirror  
]
>
After referring to the User's guide, if you still need assistance, call Brother  
Customer Service at:  
>
>
[Txt&Format]  
.
All text and settings will be  
cleared.  
[Mirror Prt?]  
You can also use the Function shortcuts for these menu. Press the  
and the shortcut key shown next to the menu title. To confirm,  
If you need to locate a service center, please call 1-877-BROTHER or visit  
press  
.
Use clear tape in [Mirror], so the labels can be read correctly from the oppo-  
site side when attached on glass, windows or other transparent surfaces.  
[Text Only]  
.
Only text will be cleared.  
 

Beko Washer WCB75087 User Manual
Bel Canto Design Stereo Amplifier PHONO 1 User Manual
Billy Goat Vacuum Cleaner KD501 User Manual
Blaupunkt CD Player Sydney RCM 126 User Manual
Bolens Lawn Mower 120 848E000 User Manual
BOXLIGHT Projector CP 320t User Manual
Briggs Stratton Lawn Mower 110000 User Manual
Broan Work Light 744SFL User Manual
Canon Camera Lens EF55 200mm f 45 56 II USM User Manual
Chief Manufacturing Tool Storage CMA470 User Manual